There are many types of copper door handles and handles available for copper doors, including levers, hardware screen doors, pin sleeves, core locks, door handles, and knobs. These may be small devices, but they have significant differences in functionality and also depend on your door. When these devices become dirty or broken, they may become a major headache for you. It is important to be careful and patient when cleaning copper doors, We can't be lazy about cleaning the copper door for a long time. Below, Guangzhou Dingyi Copper Door Factory will teach you how to clean the copper door handles and handles.

所有的的门硬件设备可在一定范围内的材料，包括黄铜，铜，银，重要的是他们正确的清洁和维护，黄铜的门把手是非常普及的今天，只是因为近复兴的老建筑，此外，黄铜是已知的用于其自我性能，但是，它仍然需要定期清洗，以使其使用寿命更长，以及提高看。

All door hardware devices can be made of materials within a certain range, including brass, copper, and silver. It is important to clean and maintain them correctly. Brass door handles are very popular today, just because of the recent revival of old buildings. In addition, brass is known for its self disinfection performance, but it still needs to be cleaned regularly to make its service life longer and improve its appearance.

清理铜门把手和拉手钢铜门的流程

The process of cleaning copper door handles and handle steel copper doors

除了污垢和一般的污垢，因为日常使用，铜门黄铜门把手和硬件很容易变色，这通常发生由于金属向反应在空气中的某些元素，浸在盐半颗柠檬汁擦到的黄铜门把手和手柄，然后，用柔软的布或棉花擦拭干净，你会得到你的设备再次清洁，这的清洁技巧也有帮助，在清洁的铜配件。

In addition to dirt and general dirt, copper doors, brass door handles, and hardware are prone to discoloration due to daily use. This usually occurs when the metal reacts with certain elements in the air, and the brass door handles and handles are soaked in half a lemon juice in salt. Then, wipe them clean with a soft cloth or cotton, and you will get your equipment cleaned again. This cleaning technique is also helpful in cleaning copper accessories.

镀银或纯银的设备也很好看，但楼市泡沫破裂打碎很容易，要清理这些设备，拆卸，并把它们放在一个玻璃盘或铝盘，在这些项目上洒一些小苏打，然后倒入开水，几分钟后，他们用非研磨性的布擦拭干净，定期用肥皂水清洗，除了这些技术也是必不可少的。

Silver plated or pure silver equipment is also very beautiful, but it is easy to break the foam in the real estate market. It is necessary to clean these equipment, dismantle them, put them on a glass plate or aluminum plate, sprinkle some baking soda on these items, and then pour boiling water. After a few minutes, they use non abrasive cloth to clean them, and regularly use soapy water to clean them. In addition to these technologies, they are also indispensable.

清理铜门把手和拉手钢铜门的流程

The process of cleaning copper door handles and handle steel copper doors

测量墙体的厚度，门洞的宽度和高度，再测量门框的顶铜门框长度以及边框长度，检查是否与门洞相匹配。

Measure the thickness of the wall, the width and height of the door opening, and then measure the length of the top copper door frame and frame of the door frame to check if it matches the door opening.

组装门框，顶框与边框应连接成90°角，在边框的两侧，采用4—6个连接片进行固定，然后钉上锁脚铜条以及锁角铜条，顶框盖在两边框的上面，两边框档门的内宽度应该比门扇的宽度多7mm，顶框档门口与地面之间的内高度应该比门扇的高度高出13mm。

When assembling the door frame, the top frame and frame should be connected at a 90 ° angle. On both sides of the frame, 4-6 connecting pieces should be used to fix it, and then lock foot copper bars and lock angle copper bars should be nailed. The top frame should be covered on top of the two frames, and the inner width of the two frame doors should be 7mm more than the width of the door leaf. The inner height between the top frame door and the ground should be 13mm higher than the height of the door leaf.

安装门框，将组装好的门框整体放入门洞，并检查是否垂直，以连接片的钉孔为点，确定墙体上的钉孔位置，然后使用元钉将连接片固定于墙上，并在门框和墙体的缝隙嵌入铜条，保证门框与墙体的连接牢固，密实。

Install the door frame, place the assembled door frame as a whole into the door opening, and check if it is vertical. Use the nail hole of the connecting piece as a point to determine the position of the nail hole on the wall. Then use a metal nail to fix the connecting piece to the wall, and embed a copper strip in the gap between the door frame and the wall to ensure that the connection between the door frame and the wall is firm and dense.

安装门扇合页，先在铜门上下合页拧一枚螺丝钉，然后关门，检查缝隙是否合适，以及档门口与门扇是否处于同一平面，确保档门口无错位，门扇不下坠，然后将其它螺丝钉拧紧，禁止将螺丝钉直接钉入门框内，安装门框与门扇时，应确保档门口一致，门扇，门锁开闭灵活，门扇四周的缝隙合理一致，连接缝隙牢固严密，装饰表面无损坏。

To install the door leaf hinge, first tighten a screw on the upper and lower hinges of the copper door, then close the door, check if the gap is appropriate, and whether the door sill and door leaf are in the same plane to ensure that the door sill is not misaligned and the door leaf does not fall. Then tighten other screws, and do not directly nail the screws into the door sill. When installing the door frame and door leaf, ensure that the door sill is consistent, the door leaf and door lock open and close flexibly, and the gaps around the door leaf are reasonable and consistent, The connection gap is firm and tight, and the decorative surface is undamaged.

安装线条，可以根据墙体与门框的宽窄程度而定，如果出现墙比框窄的情况，可以将线条边较宽的一面靠墙，如果出现框比墙窄的情况则反之。

The installation line can be determined based on the width of the wall and door frame. If the wall is narrower than the frame, the wider side of the line can be placed against the wall. If the frame is narrower than the wall, the opposite is true.

为钢铜门门挡条上的扣线涂胶水，干透后扣入门挡条上的槽，这是整个安装过程中需要使用胶水的地方。

Apply glue to the fastening wire on the steel copper door stop strip, dry it thoroughly, and then fasten it to the groove on the door stop strip. This is the only place where glue is needed throughout the installation process.

有了 山东铜门上面的小总结，希望对广大客户有所帮助，如果有什么不理解的或者寻求帮助的请点击我们的网站： //www.doveish.com或者来电咨询，我们会尽全力为您解决

With the summary above Shandong Tongmen, we hope it can be helpful to our customers. If you have any questions or need help, please click on our website: //www.doveish.com Or call to inquire, we will do our best to solve it for you